Boot Seals Weatherproof WA-WGC Pipe Seals pipe not centered Pipe-Seals external units WA-GPP-T Pipe-Seals external WA-GP-B Pipe Seals- multi pipe seals WA-GP-W Pipe Seals water hammer isolation Pipe Seals & waterproof liner Pipe Seals vibration damping Pipe Sealing metal tank walls Pipe Seals axial movement WA-GP-NS Pipe Seals through floors End Seals casing pipes Pipe Plug Seals taper fit Manhole Seals joint jnflow Pipe Seal Boots Septic Tanks Connector Boots pipe to manhole Pipe Seals Weatherproof Split Boot Pipe Seals hi-temp silicone rubber Pipe Sealing Internal repair
Wall Sleeves for Large Pipes Wall Sleeves External Wall Wall Sleeves Split For Existing Pipes Wall Sleeves Split Boot Weatherproof Wall Sleeves Flange Connect Wall Sleeves Puddle Flange Wall Sleeves Tank Connection Wall Sleeves Multi-Conduit Wall Sleeves Tempoary Entry
Casing Spacers non-metallic Casing Spacers Multi Pipes Casing Spacers - Steel Casing Spacers Adjustment Legs Casing Spacer with Joint Restraint
Repair Clamp Split Bolted Repair Clamps Flange Leak Repair Clamps Pit Hole Leaks Repair Clamps Encapsulating Repair Clamps Pipe Bends Repair Inside Pipe Leak
Couplings Pipe Restraint Pipe Couplings Plastic PVC Couplings PVC To Steel Pipe Couplings Stainless Pipe Repair Bell Restraint Couplings High Pressure Pipe Couplings
Pipe Plugs Pneumatic Pipe Plug sectional large pipes Pipe Plugs Mechanical Packers Pipe Repair Internal
Heater Wraps Totes Heater Wraps DRUMS Heater Wraps PUMPS Heater Wraps TANKS Heater Traps CONCRETE Pipe Heater Wraps Drum Ovens 4 Barrel Heaters
BUILDING ENTRY PIPE SEALS
PUDDLE FLANGE EDPM PIPE SEALS
MANWAY HATCH COVERS
FLANGE ISOLATION KITS
MONOLITHIC ISOLATION JOINTS
Stainless Steel Tapping Sleeves
Stainless steel tapping Sleeves (hot) taps on several pipe types for water, gas and petrochemical fluids
The SST is a reinforced split boltable double band clamp with a flanged connection outlet.
The upper body is reinforced to accomodate the installation of valves and drilling equipment.
The SST tapping sleeve is designed for live placement drilling (hot taps).
Tapping tee clamps for pipe diameters from DN 80 up to DN 800. Standard length: 500 mm.
Other lengths are available.
The built-in OD range of 20 mm allows one sleeve to ﬁt various classes of steel, PVC, ductile iron, cast iron or asbestos-cement pipe.
No specially trained personnel or tools needed. A wrench to tighten bolts is the only tool required to install the sleeve.
Full circumferential seal:
Allows you to tap size on size with conﬁdence. No more need for heavy, hard to assemble, cast iron sleeves.
Stainless steel AISI 304 or 316 L.
The high tensile strength of stainless steel allows us to manufacture the lightest tapping sleeve in the industry. Easy to handle and less load on the pipe.
Full circle design reduces stress on the pipe opposite of the tap.
Threaded connection tees stainless steel tapping clamps are used to make permanent (hot) taps on different pipe types. For water, gas and petrochemical fluid applications.
Threaded Tapping repair clamps can be equipped with a threaded outlet up to 4". The standard outlets are threaded according to ISO/ DIN or BSP. American CC or IP threads are available as well.
The clamps can be used to repair the following pipe types:
- Ductile Iron (DI)
- Cast Iron (CI)
- Steel (St.)
- Asbestos Cement (AC)
PE coated steel
- PVC, GRP, PE
All metal parts: stainless steel AISI 304 or AISI 316L.
Sockets and nipples are threaded according to ISO 7/DIN or BSP. Special designed outlets are available on request.
The outlets are 100 % air tested after welding.
Metal parts have been deburred and are passivated to restore the corrosion resistance to its original state after the welding process.
Single band (one section) or double band (two sections). For detailed working ranges please see our price-list.
Standard certiﬁed rubber gaskets EPDM or NBR. The rubber is tapered and has a waffle pattern.
Seamless rubber lining for every clamp diameter.
Bridge plate is vulcanized into the rubber gasket.
U-shaped lifter bars.
Stainless steel, electrolytic zinc plated nuts to prevent galling.
Stainless steel washers.
No loose parts that may get lost during installation.
No special tools required: a simple wrench will do the job.
Special tape is used to ﬁx the rubber gasket to the stainless steel band. This tape is ﬂexible and reinforced with glassﬁbre thread to withstand hot and humid conditions and guarantee a long storage capability.
Under most circumstances the clamps can be installed without releasing the pressure on the pipe.
FS 10 tapping clamps are available from range 38-42. Available lengths: 150 / 200 / 250 / 300 / 400 / 500 / 600 mm.
FS 20 tapping clamps are available from ranges 88-110. Available lengths: 200 / 250 / 300 / 400 / 500 / 600 mm.
Pressure ratings for water ** depend on the type of break or damage, pipe OD, medium etc.
Pipe DN 40 up to and including DN 150: 16 bar
Pipe DN 175 up to and including DN 300: 10 bar
Contact us: Westatlantic Tech Corp., 902 455 4455
USA Canada: Threaded Pipe tapping Sleeves. USA: Texas, TX, Houston, New York, NY, Illinois, IL, North Dakota, ND, Iowa, IA, Ohio, OH, Michigan, New York, NY, Utah, Arkansas, Kentucky, KC, California, CA, Colorado, Denver, Louisiana, LA, Florida, FL., Pennsylvania, PA. Wisconsin, WI. Canada, Ontario, Oakville, Toronto, London, Hamilton, Mississauga. Alberta, AB; Edmonton, Fort McMurray Calgary. British Colombia, BC; Kelowna, Vancouver, Prince Rupert, Kitimat. Saskatchewan, SK; Regina, Saskatoon, Prince Albert, Estevan, Swift Current. Manitoba MB; Winnipeg, Thompson. Quebec, QC; Montreal, Quebec City, Trois-Rieviers, Chebougamau, Sherbrooke. QC, Alberta, Saskatchewan, Manitoba, Quebec, New Brunswick, NS, Newfoundland. ROMACON, UNI Coupling, United Pipeline Products, Romacon Petro, Hegawa, Gekave.